Toshiba VFPS1-2007PL inverter 0.75 kW 3-phase 220 V (VF-PS1)

VFPS1-2007PL is a Toshiba VF-PS1 inverter – pump and fan inverter up to very large capacities. It controls 3-phase induction motors up to 0.75 kW from a 3-phase 200 – 240 V supply, with built-in EMC filter (PL suffix).

Toshiba's dedicated pump and fan range; according to Toshiba, VF-PS1 includes very large models for plants and infrastructure. Optimised energy saving for variable-torque loads, with PID and energy-saving modes. PL models include a built-in EMC filter.

Reading the code: VF-PS1 is the range; the digit after the dash is the voltage class (2 = 200 V, 4 = 400 V); the next three digits give the rating (0.75 kW); PL includes an EMC filter, PM does not. Size the drive by the rated current on the 220 V motor nameplate; for heavy starting (loaded conveyors, crushers, compressors) choose one size larger.

TOVINA distributes Toshiba inverters in Vietnam, with engineers for sizing, wiring, parameter setup, retrofits and repair. Operation videos by TOVINA are below. Contact +84 0917 399 279.

Product videos

VF-PS1 features

• Toshiba's dedicated pump and fan range; according to Toshiba, VF-PS1 includes very large models for plants and infrastructure.
• Optimised energy saving for variable-torque loads, with PID and energy-saving modes.
• PL models include a built-in EMC filter.
• Suits water supply and drainage pumping, wastewater treatment and large exhaust fans.

Sizing and accessories

• A 0.75 kW drive suits 220 V motors up to 0.75 kW on standard loads; compare the drive rated current with the motor nameplate.
• For heavy starting, frequent reversing or panel temperatures above 40 °C, choose one size larger.
• For fast stops of high-inertia loads (large fans, centrifuges, cranes), fit a braking resistor of the recommended value.
• For long motor cables or several motors on one drive, ask TOVINA about output reactors and settings.
• Protect the input with a correctly rated breaker or fuses; do not switch an output contactor to start/stop the motor.

Installation and wiring

• Connect the supply to R/L1, S/L2, T/L3 and the motor to U/T1, V/T2, W/T3 – never apply mains to U, V, W.
• Earth the drive and motor; route signal cables away from power cables to reduce noise.
• Mount vertically with clearance above and below for cooling; sealed panels need a fan.
• After power-off, wait until the capacitors discharge (charge lamp off) before touching terminals.

Basic setup

• Use the keypad Setup Wizard to enter motor data, command source and frequency source step by step.
• Set acceleration/deceleration, frequency limits and motor overload protection from the motor nameplate.
• Back up parameters to the keypad to copy them to a spare drive.
• Toshiba setup videos are below; TOVINA commissions the drive at handover.

Routine maintenance

• Clean dust from the heat sink and cooling fan; replace noisy or weak fans.
• Re-tighten power terminals after a period of operation; look for signs of overheating.
• Review the trip history to catch overcurrent, overvoltage and overheating early.
• Power up spare drives periodically to keep the capacitors in condition.

VF-PS1 drives at TOVINA

• VFPS1-2007PL — 0.75 kW — 3-phase 200 – 240 V

FAQ

• What motor size does VFPS1-2007PL drive? 220 V motors up to 0.75 kW on standard loads; choose a larger size for heavy duty.
• What supply does it need? 3-phase 200 – 240 V.
• Does it have an EMC filter? Built-in EMC filter (PL suffix).
• Does TOVINA provide setup and repair? Yes: sizing advice, parameter setup, wiring, operator training and repair of Toshiba drives.